hamradiotools

Nexus 0.12.0

RTTY goes hands-free, SSTV FSK-ID + a real FT8 sensitivity fix. Released 18 July 2026. The current release is 1.24.0. Download it · Every version

Fixed — on-air transmit pass (RTTY/SSTV) + Raspberry Pi

  • RTTY and SSTV now key with power.

    Both armed and asserted PTT but radiated nothing on the common Icom / default-Yaesu setup: they commanded plain LSB/USB, where the rig takes TX audio from the mic, not the USB codec. They now command a DATA submode (PKTLSB/PKTUSB) before keying — the same routing FT8 uses — so the soundcard audio actually modulates. Rig-agnostic through Hamlib (Yaesu DATA / Icom -D / Kenwood DATA).

  • Enable-TX arm in the RTTY and SSTV cockpits.

    Transmit is off by default (WSJT-X "Enable Tx"), but those screens gave no way to arm it, so every send hit "TX is off." The cockpit header's TX pill is now a click-to-arm control.

  • Raspberry Pi (aarch64) support.

    Nexus now builds an arm64 .deb for 64-bit Raspberry Pi OS (Pi 3/4/5). On a slower Pi, Settings ▸ Decode depth ▸ Fast keeps FT8/FT4 decoding real-time. (Fixed an ARM-only c_char signedness bug in the modem FFI.)

  • CW copilot recovers space-split callsigns.

    When CW copy dropped a gap mid-call ("W1 ABC"), the clean call you read never became a clickable chip. It now rejoins a real prefix|suffix split (validated against DXCC) so those calls are clickable again.

  • Phone push-to-talk is a normal button, not a full-width bar

    — reclaims the row.

  • Clicking an FT4 spot switches the decoder to FT4

    (then QSYs to the spot) instead of leaving you on FT8.

  • The live S-meter reading is ~3× larger

    on the Phone and CW scopes.

Fixed — FT8/FT4 decode sensitivity (measured)

  • Anti-aliased receive audio.

    The capture path's 48 kHz→12 kHz conversion previously took every 4th sample with no filtering, folding all supersonic noise (6–24 kHz) from the soundcard/interface straight into the decode band. It now runs a proper 64-tap anti-alias decimator (fc 4500 Hz — same spec as WSJT-X's, with deeper stopband). Measured on paired test audio: up to +4 dB of effective sensitivity on a noisy audio chain, and a doubled-to-tripled decode rate at the −21 dB weak tail even on a clean chain. Benchmarked against stock WSJT-X's decoder on identical audio, Nexus's decode floor now sits at −21.3 dB vs stock's −20.7, with zero false decodes.

  • Busy slots no longer drop decodes.

    The per-slot decode limit was 64 (weakest arrivals silently discarded on crowded bands); now 200, matching WSJT-X. Applies to FT8 and FT4.

  • Cross-cycle deep recovery (a7) fixed

    : the early decode pass was double-writing the a7 candidate table (halving its capacity), and the table wasn't cleared on radio swap or a VFO-knob band change. Both fixed — a7 recoveries now work at full strength.

  • Field Day AP decoding

    : your callsign now feeds the a-priori decoder during Field Day operation, so "MyCall ???" deep recoveries work there like normal operation.

Fixed — rig control, RTTY, roster, scaling

  • Dual same-model Icom radios now work.

    With two Icoms configured, mode-setting failed on both ("rig has no PKTUSB mode") and only worked after deselecting one — a radio-handoff isolation bug that double-commanded the outgoing rig on every contended switch. Fixed. (Plus: rigs on a slow CAT link — ≤19200 baud, the IC-7610's factory default — now get a longer reply deadline, a mode-set fallback ladder, and honest "link too slow / press the rig's DATA key" messages instead of a dead-end.)

  • RTTY no longer prints garbage on an empty frequency.

    The Baudot demod had no squelch, so band noise decoded into a stream of random characters. Added a signal-presence squelch (calibrated so noise is silent but a −2 dB signal still copies).

  • The FT call roster reads as "live now."

    Tightened the drop-off to 3 T/R cycles (~45 s on FT8) and added an age fade — stations dim as they go quiet, so who's active right now stands out.

  • UI scaling controls work correctly.

    The Manual scale strip no longer overflows its container (options past 110% are reachable again), Auto's max-scale chips are disabled when the window can't use them (no more "150% = 175%"), the Comfortable/Compact density switch now actually changes row spacing, and Settings tabs can't be clipped at any scale.

  • 3-D globe (Connect) spot hover

    now shows the same rich tooltip as the 2-D map (callsign, band/mode, frequency, age, "heard you") instead of just the callsign.

Fixed — controls & frequencies

  • TX Power controls now match and apply live.

    The Settings "Tx Power" and the cockpit "Pwr" slider are the same value (the audio drive into the rig — not the rig's RF watts); Settings now applies on release and both stay in sync in both directions.

  • RTTY/SSTV band-plan corrections

    (checked against ARRL + IARU R1 + community convention): RTTY 80 m moved 3.580 → 3.590 (3.580 is PSK31), RTTY 40 m split into 7.080 (US) + 7.045 (EU/DX), SSTV 80 m split into 3.845 (US) + 3.730 (EU), 12 m RTTY segment note corrected.

Added

  • SSTV transmit — send pictures on the air.

    The SSTV cockpit now has a Transmit panel: drop in an image, pick a mode (all 15 — Scottie, Martin, PD, Robot), see a live preview cropped to that mode's exact resolution, and Send. It transmits as USB voice audio through the safety-gated TX path (nothing keys until you press Send, guaranteed unkey, a hard duration cap), with a progress bar and one-click Stop. Verified end-to-end: every mode encodes and decodes back through Nexus's own receiver.

  • RTTY auto-sequencer — hands-free QSOs.

    Turn on Auto in the RTTY cockpit, then click CQ to run or Answer a decoded caller: the exchange sends, the contact auto-logs (mode RTTY), and the closing 73 goes out — the same operating discipline as the FT8 sequencer, over the safety-gated RTTY keyer. Nothing ever transmits on launch or on toggling Auto; only an explicit CQ/Answer keys up.

  • RTTY waterfall with mark/space cursors + click-to-net.

    The RTTY cockpit now shows a waterfall with cursors marking the mark and space tones; click a signal to net the decoder onto it (re-acquires AFC around the new center).

  • RTTY spots on the Needed board.

    Reverse Beacon Network RTTY skimmer spots now appear as RTTY rows (governed by the Digital filter chip); one click QSYs and opens the RTTY cockpit.

  • RTTY & SSTV in the setup wizard.

    The first-run wizard now offers RTTY and SSTV as operating modes alongside Phone and CW.

  • SSTV FSK-ID capture.

    The callsign FSK ID that trails an SSTV image is decoded and shown on the gallery entry (best-effort — a callsign appears only when cleanly recovered).

  • Auto-arm SSTV for ISS passes (opt-in).

    When enabled in Settings, Nexus tunes 145.800 FM and arms the SSTV decoder when the ISS is overhead, then restores your dial at LOS. Off by default; never retunes without the opt-in.

Fixed

  • The RX Gain slider now applies to the live audio as you use it.

    Previously the slider only updated its label and didn't reach the running capture stream until you hit Save — so the RX Level meter never moved while dragging and the control looked dead. It now commits the new gain to the live stream when you release the slider (or after a keyboard adjustment), so the meter responds immediately. (Decoding was never affected — the gain always applied on Save.)

  • The "update available" notice now appears reliably on launch.

    The launch check was gated by a once-per-day throttle that also suppressed the display (not just the network fetch), and every manual "Check for updates" reset that timer — so for anyone who launches often or uses the button, the launch prompt was effectively never shown while the manual check always worked. The check now runs on every launch (a single small request) and surfaces the prompt whenever a newer build exists and that version hasn't been dismissed via Download.

Changed

  • Update checks now read the app's own endpoint

    (hamradiotools.io/nexus/version.json), falling back to SourceForge's best_release.json if it's unreachable — so update accuracy no longer depends on the per-release SourceForge "Default Download" flip. The "Download" button now opens the GitHub Releases page (primary distribution; SourceForge mirrors it).

Every version