hamradiotools

Nexus 0.8.5

Native Icom phone toolkit (RF panadapter, TX meters, mic gain) + CI-V PTT fix. Released 14 July 2026. The current release is 1.24.0. Download it · Every version

Fixed

  • Native Icom CI-V: transmit no longer flickers the PTT (IC-9700 and friends).

    With the native CI-V path on, hitting Tune or transmitting keyed the rig and then unkeyed it ~50 ms later — a fast "click," TX light but no RF. Two stacked root causes, found via the new CI-V diagnostic log: (1) A Windows-only socket bug killed every CAT connection after ~one command. On WinSock — unlike Linux, where all our tests run — a socket returned by accept() inherits the listener's non-blocking mode. The native daemon's rigctld listener is non-blocking, so every accepted connection's first idle read errored and the server closed it: Nexus's own rig-control link was silently reconnecting for every command all session. Accepted connections are now reset to blocking. (2) The disconnect fail-safe stole our own transmit. The daemon's rigctld server unkeys the radio when a PTT-asserting client disconnects (so a crashing WSJT-X/N1MM can't strand the rig keyed) — and the constant churn from (1) meant the connection that keyed always died moments later, unkeying the over. The fail-safe now stands down while Nexus itself is transmitting (published to the broker at every keying site, so there's no race), and still fires for a genuine external-client crash. (The scope-waveform stream is a separate matter — see the 115200-baud fix below.)

Added

  • Native Icom scope: the IC-9700's "no scope" mystery solved — it's the rig's baud requirement.

    Per Icom's own CI-V reference, wave-data output over USB requires CI-V USB Baud Rate = 115200 ("Unlink from [REMOTE]"); at lower rates the rig refuses to stream (NAKs the enable) even though CAT works fine. Nexus now: gates the scope stream at 115200 (matching the rig instead of inviting the refusal), pins the Main scope on dual-receiver rigs (IC-9700/7610) before enabling the stream, and spells out the exact rig menu settings in the native CI-V hint. If your waterfall shows no "CI-V RF": set the rig and Nexus to 115200.

  • Phone cockpit: the native scope is now a real RF panadapter.

    When a FlexRadio or Icom CI-V scope is streaming, the Phone cockpit drops the audio-passband framing (the "RX audio" label and the audio-Hz span chips) and shows the rig's actual RF spectrum full-width, with RF zoom presets (Full / ±25k / ±10k / ±5k) instead of a passband-width sliver. Audio-derived scope is unchanged.

  • Phone cockpit: transmit meters (SWR / ALC / Po / COMP).

    While you transmit, colored meter bars appear where the S-meter sits — SWR (antenna match), ALC (set your mic gain against it on SSB), output power in watts, and speech compression — using the exact IC-9700 calibration curves, so the readings match the rig. Only the meters your rig actually reports show; all blank on unkey.

  • Phone cockpit: mic-gain slider.

    A mic-gain control beside the power slider (when the rig reports it) so you set SSB mic gain from Nexus while watching the ALC meter — no reaching for the radio. Mirrors the real rig level.

  • Native Icom CI-V: the DSP buttons (NB / NR / ANF / COMP / VOX) now work.

    They were live only on the Hamlib path; on the native CI-V path the rig never reported the states, so the buttons stayed hidden. Nexus now reads and sets them over CI-V, so the cockpit's DSP toggles light up and work.

  • CI-V bus diagnostic log (Settings ▸ native Icom CI-V).

    An opt-in support tool that records the raw CI-V bus traffic — every byte to and from the radio, timestamped and decoded (PTT on/off, mode set, scope waveform, ack…) — to a file in your Downloads. It's the way to root-cause hardware-only native-CI-V faults (like the IC-9700 PTT flicker on transmit): turn it on, reproduce the issue, turn it off, and the capture shows exactly what's on the bus during the fault. Off by default, not persisted, and free when off (the engine only taps the wire while it's armed).

Changed

  • FT8 Call Roster now leads with the callsign, then the Need column.

    Callsign is the first thing operators scan, so it moves to the front; the Need column (need chips + rarity pill) follows it, reading as "why you'd want this station" right after the call.

Every version